| Casting Number |
8840 |
| Description_ABR |
Water Pump |
| Description_ASM |
Ford:V8 F-Series Trucks:302 (5.0L)-351 (5.8L) |
| Description_DEF |
Engine Water Pump |
| Description_DES |
FITTING |
| Description_EXT |
Edelbrock #8046 Polished water pump for 1993-97 F Series, 5.0/ 5.8L |
| Description_EXT |
Edelbrock #8046 Polished water pump for 1993-97 F Series; 5.0/5.8L |
| Description_FAB |
Equal Distribution to Both Sides of Block |
| Description_FAB |
Impeller Is Larger Than Others For Max Pressure |
| Description_FAB |
Impeller Vanes Dramatically Increase Flow Rates |
| Description_FAB |
Internal Passages Are Balanced for Maximum Flow |
| Description_FAB |
Maximum Cooling for Street and Racing Engines |
| Description_FAB |
Only Flows In One Direction For Optimum Efficiency |
| Description_INV |
Water Pump SBF1965-68 289 1968-69 351w P |
| Description_KEY |
Edelbrock; Water Pump; 8046; Ford; 5.0L; Late Model; 302; |
| Description_LAB |
Water Pump Ford 5.0L Late Model in Polished Finish |
| Description_MKT |
Edelbrock #8046 Polished water pump for 1993-97 F Series, 5.0/ 5.8L V8, using a serpentine accessory drive belt. Not for early model 289-302, will not fit 1994-1995 Mustang provides maximum cooling form the street and the race track. Water pump provide maximum flow, maximum pressure and equal distribution to both sides of the block with 1%. |
| Description_SHO |
{ Sellable : Yes } |
| Description_SHP |
{ eo : 0in.} |
| Description_TRA |
Be sure that the fan bolts don't protrude through the hub so far that they hit the water pump housing |
| Description_TRA |
Check closely for any interference with drive belts |
| Description_TRA |
Consult service manual for specific procedures, if necessary |
| Description_TRA |
Incorrect alignment or an unbalanced condition puts excessive strain on the pump's shaft and/or bearing and will result in early failure of the shaft and/or bearing. The balance of the assembly depends primarily upon the concentricity of the fan clutch with the pump shaft. Concentricity is not assured when universal type clutches are used. The universal fan clutch has a 3/4" pilot hole, so an adapter must be used when installing a water pump with a 5/8" shaft. This adapter bushing is supplied with the unit. These adapter bushings add to the machine tolerances of the assembly, so special care must be taken to maintain concentricity with the shaft and the clutch fan. The use of aftermarket (non-OEM) fan spacers are not recommended and will void the warranty of the water pump. |
| Description_TRA |
Installation is the same as for original equipment water pumps |
| Description_TRA |
Reassemble backing plate and install on engine using RTV silicone |
| Description_TRA |
Remove two screws from backing plate and apply RTV silicone to gasket just before installation |
| Description_TRA |
some filing for clearance may be necessary with some applications |
| Description_TRA |
The distance from the flange surface to the hub should measure 5.75". |
| Description_TRA |
• Installation is the same as for original equipment water pumps • Consult service manual for specific procedures; if necessary • Remove two screws from backing plate and apply RTV silicone to gasket just before installation • Reassemble backing plate and install on engine using RTV silicone • Be sure that the fan bolts don t protrude through the hub so far that they hit the water pump housing • Check closely for any interference with drive belts; some filing for clearance may be necessary with some applications • The distance from the flange surface to the hub should measure 5.75in. Incorrect alignment or an unbalanced condition puts excessive strain on the pump s shaft and/or bearing and will result in early failure of the shaft and/or bearing. The balance of the assembly depends primarily upon the concentricity of the fan clutch with the pump shaft. Concentricity is not assured when universal type clutches are used. The universal fan clutch has a 3/4in. pilot hole; so an adapter must be used when installing a water pump with a 5/8in. shaft. This adapter bushing is supplied with the unit. These adapter bushings add to the machine tolerances of the assembly; so special care must be taken to maintain concentricity with the shaft and the clutch fan. The use of aftermarket (non-OEM) fan spacers are not recommended and will void the warranty of the water pump. |
| Engine Make/Size |
Ford 5.0L/302 |
| Fan Clutch Included |
No |
| finish |
As Cast |
| height |
8.5 |
| Housing Material |
Aluminum |
| Hub Height |
5.420 |
| Hub Hole Quantity |
6 |
| Impeller Material |
Powdered Metal |
| Impeller Rotation |
Reverse |
| Impeller Vane Quantity |
6 |
| Includes Back Housing |
Yes |
| Installation Warnings |
Yes |
| length |
13.7 |
| Mounting Hardware Included |
No |
| Mounting Hole Quantity |
11 |
| Outlet Quantity |
1 |
| Pulley Included |
No |
| Related Cooling Fan Components |
No |
| RGL |
WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov. |
| Style |
Street/High-Performance |
| Thermostat And Housing Included |
No |
| Type |
Mechanical |
| WARNING CA Proposition 65 |
Yes |
| WARNING CA Proposition 65 Message |
WARNING: This product can expose you to Lead; which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information; visit www.P65warnings.ca.gov. |
| Water Pump Drive Type |
V-Belt |
| weight |
9.7 |
| width |
9.2 |
